Unitree G1 Introduction and Safety#
Before working with the physical Unitree G1, review the workflow-specific safety checkpoints for teleoperation, data recording, and policy deployment.
Support is bounded to the hardware and software releases documented for v0.1. Physical hardware behavior is not tested by repository CI.
Important
This documentation is a workflow guide, not an operating guide for the Unitree G1. Use the manufacturer’s documentation and your organization’s robot-safety procedures for operation, stop and abort behavior, power-on, power-down, recovery, maintenance, and lab approval.
For the complete procedure order and supported hardware, see the Unitree G1 real static apple workflow path.
Safety Protocols#
Danger
The Unitree G1 is a powerful humanoid robot with substantial mass and moving limbs. Improper operation can injure people or damage the robot and workspace. Follow all approved safety protocols.
Workflow Safety Checks#
Complete these checks before every teleoperation, recording, or deployment session:
[ ] Clear unnecessary objects and obstacles from the workspace.
[ ] Verify the table and task objects are positioned correctly.
[ ] Route every cable so it cannot interfere with robot motion.
[ ] Ensure at least one person can activate the approved external stop or abort mechanism at all times.
[ ] Use at least two people: one operator and one safety monitor.
[ ] Keep bystanders outside the robot’s reach envelope.
Stop and Abort Procedure#
Important
The Unitree G1 does not include a built-in e-stop button. The workflow’s ROS safety controller can stop robot motion, but it does not fully replace an e-stop.
Stop the robot during teleoperation or deployment in this order:
Disable control first. Set
blend_ratioto0.0on the active ROS safety controllers. Use the exact commands in the teleoperation and deployment procedures.Stop the ROS launch stack. Press Ctrl+C in its terminal and wait for the process to exit cleanly.
Disconnect Ethernet only as a last resort. If the robot still behaves unexpectedly, disconnect the Ethernet cable between the Unitree G1 and Thor to cut motor commands.
Avoid disconnecting Ethernet while robot control remains enabled. Stopping the stack first allows the ROS safety controller to ramp down cleanly.
Manufacturer Operating Procedures#
Use Unitree’s procedures for power-on, power-down, recovery, and emergency behavior. This workflow is not the authority for those procedures.
Operational Safety Guidelines#
Never place hands or body parts within the active workspace during autonomous operation.
Maintain visual contact with the robot throughout policy deployment.
Start new policy tests at slow execution speeds.
If behavior becomes unexpected, activate the approved stop or abort mechanism immediately. Do not physically restrain the robot.
Robot Setup#
Connect Thor to the Unitree G1 with:
USB from the head-mounted RealSense camera to Thor. Plug it directly into a Thor backpack, or use a USB extension cable for an external Thor.
Direct Ethernet from the Unitree G1 to Thor for network communication. Do not insert a network switch or USB-to-Ethernet dongle.
The intended topology is one USB camera connection and one direct Ethernet control connection between the Unitree G1 and Thor.
Workspace Setup#
The task is a left-handed tabletop pick-and-place: the robot picks up a red apple and places it on a white plate.
Place the Unitree G1 at a table approximately 75 cm high and cover the table with a black tablecloth. Put a red apple on the robot’s left and a white circular plate, approximately 19 cm in diameter, on its right. Use a white wall behind the table. Keep both objects in the head-mounted RealSense camera’s field of view and within comfortable reach of the left arm. Establish a safety perimeter, an operator station outside the reach envelope, and lighting that illuminates the task surface uniformly.
Important
The apple must start to the left of the plate. The pretrained policy was trained only on that arrangement.
Lighting#
Keep lighting stable between data collection and deployment. Eliminate harsh table shadows, avoid direct glare on the camera, and illuminate the full workspace uniformly.
Robot Start Pose#
Place the Unitree G1 pelvis very close to the table edge, touching or lightly pushing against it. Face the robot toward the table. Keep the head neutral so the neck plane remains parallel to the top of the torso.
Next Stage#
The workspace, cable routing, stop access, and two-person operating roles must be ready before control is enabled. Continue to Isaac ROS Setup on Thor to prepare the software environment and verify the RealSense camera.